Categories

Waterway Executive 48, 1.5HP 2 Speed, Pump 2" in-out 2", PF-15-2N22-4

Reg: $565.76
$384.99
(You save $180.77 )
(3 reviews) Write a Review
SKU:
3420620-1A
Brand:
Availability:
Usually ships in 1-2 days.
Shipping:
Calculated at Checkout

Waterway Executive 48 1.5 HP pump


Waterway's Executive 48 frame hot tub pump which has 1.5 HP and 2 speeds is a suitable replacement for most older hot tub pumps of the same size with the same specs. This pump has 2 speeds running at 3450 RPM on high speed and 1725 RPM on low speed.


Pump details:

  • 1.5HP Waterway Executive 48 Spa Pump,
  • 2 Speed 
  • Waterway OEM part # 3420620-1A
  • 2.0" intake and 2.0" discharge,
    (Actual measurements are are 3" outside to outside thread on intake and discharge)
  • 220-240volt,
  • 8.0 Amps high speed (3450 RPM)
  • 2.6 Amps low speed (1725 RPM). 
  • New cord and unions not included, sold separately.
  • May or may not have a Capacitor on top of electric motor, shown with in picture.
  • We Include, 2 union O-rings automatically added to cart at checkout.
    When replacing a hot tub pump it is recommended to replace the union O-ring as they can develop flat edges from being compressed over the years and when a new pump is installed without replacing the O-ring the union can leak and if over tightened will crack.

IMPORTANT
The PF- model number from your old pump should not be used as a reference for selecting a new replacement pump as Waterway has produced up to 4 known variations of pumps with the same model number which are different enough that they are not interchangeable. Always select a replacement pump with the same part number as the Waterway part number on the label on your old pump.


Orientation of wet end.

Pump wet end can be oriented in 90 Degree increments, up, left or right. Pump will ship with discharge directed up. To change the discharge orientation, loosen the pump's four through bolts from the back of the motor and pull them back enough to disengage. Then rotate the wet end to the desired position, realign and re-tighten the bolts.  

 
 
 
 
Wet End Dimensions Waterway
Important
Determine the pump plumbing size by measuring the outside diameter of the wet end male threads. Plumbing sizes for hot tubs are nominal, and not actual outside diameter (O.D.) of the the threaded intake or discharge. Once you have removed the pump, use a tape measure to check your old pump thread size and compare to the sizes below.
 
If your pump thread O.D. is (approx.) 2 3/8",  Then you'll need a pump with union size 1 1/2".
If your pump thread O.D. is (approx.) 3.0",     Then you'll need a Pump with union size 2.0".
If your pump thread O.D. is (approx.) 3 5/8",  Then you'll need a Pump with union size 2 1/2".
 
Please note!
Some brands of hot tub spa pumps have non-standard threads and use fitting sizes with different dimensions. These brands are: Hayward, Jacuzzi and sta-rite.
 
 
Manufacturers 1 year limited warranty.

3 Reviews Hide Reviews Show Reviews

  • 4
    1.5hp pump

    Posted by Anonymous on 18th Jan 2018

    hot tub is up and running again with new pump

  • 5
    hot tub pump

    Posted by Unknown on 4th Aug 2016

    Best service ever! Quickest shipping and precise filling of order. Will shop here again.

  • 5
    OK

    Posted by Al on 23rd Nov 2015

    Nice to know there is actually a store in Canada that ships from in Canada that has good prices and really good service if you need. Definitely will be buying here again.